ID X5 Modem 升级固件并更新opt文件 |
您所在的位置：网站首页 › 凌动x5 e8000 › ID X5 Modem 升级固件并更新opt文件 |
ID X5 Modem 升级固件并更新opt文件
|
ID X5 Modem 升级固件并更新opt文件 主要使用的命令汇总： fis load linuxexec -c "root=/dev/mtdblock2 console=ttyS1,9600 single"passwdroot / P@55w0rd!service idirect_falcon stopifconfig | grep inetifconfig ixp0 192.168.222.220 netmask 255.255.255.0mount -t tmpfs -o remount,size=32M /tmpdf -htftp_package.sh 192.168.222.221 evo_x5_bsp-15.0.5.1.pkgmount -t tmpfs -o remount,size=32M /tmpdf -htftp_package.sh 192.168.222.221 evo_x5_rmt-15.0.5.1.pkg/usr/sbin/falcon --versiongrep modem_sn /etc/idirect/falcon/falcon.optgrep generated_by /etc/idirect/falcon/falcon.optgrep addr /etc/idirect/falcon/falcon.optrebootifconfig | grep inet/usr/sbin/falcon --versionpoweroff=================== 一、连接串口
二、在启动Linux核心 将Modem重新加电，终端显示 DRAM Test Successful 后，此时马上按空格键4~5次，进入RedBoot命令行，使用以下命令启动Linux核心。 > fis load linux > exec -c "root=/dev/mtdblock2 console=ttyS1,9600 single" DRAM Test ................................DRAM Test Successful+Ethernet eth0: MAC address 00:60:43:00:00:00IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.2Default server: 192.168.0.2RedBoot(tm) bootstrap and debug environment [ROM] release, version "iDirect 1.1" - built 12:55:42, Jun 15 2011Platform: iDirect iDS Platform (XScale) Copyright (C) 2004, 2005 iDirect Technologies, Inc.Copyright (C) 2000, 2001, 2002, Red Hat, Inc.RAM: 0x00000000-0x10000000, [0x0001c540-0x01fd1000] availableFLASH: 0x50000000 - 0x52000000, 256 blocks of 0x00020000 bytes each.== Executing boot script in 5.000 seconds - Press to abortRedBoot> fis load linux RedBoot> exec -c "root=/dev/mtdblock2 console=ttyS1,9600 single"Using base address 0x01600000 and length 0x00100000Uncompressing Linux................................................................... done, booting the kernel.Linux version 2.4.24-uc0-iDirect0 (root@EmbEserver75) (gcc version 3.3.2) #1 Wed Jun 15 12:44:25 EDT 2011CPU: XScale-IXP4xx/IXC11xx revision 2Machine: iDirect Phoenix Platform使用以下命令修改root用户(默认密码为 iDirect )的新密码为 P@55w0rd! passwd
三、建立IP连接 使用 ifconfig 临时修改接口的IP地址 / # ifconfig ixp0 Link encap:Ethernet HWaddr 00:60:43:67:69:91 inet addr:172.26.102.17 Bcast:172.26.102.23 Mask:255.255.255.248 inet6 addr: fe80::260:43ff:fe67:6991/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:302 errors:0 dropped:0 overruns:0 frame:0 TX packets:229 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:21626 (21.1 KiB) TX bytes:11898 (11.6 KiB)lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)/ # / # / # ifconfig ixp0 192.168.222.220 netmask 255.255.255.0/ # / # ifconfig ixp0ixp0 Link encap:Ethernet HWaddr 00:60:43:67:69:91 inet addr:192.168.222.220 Bcast:192.168.222.255 Mask:255.255.255.0 inet6 addr: fe80::260:43ff:fe67:6991/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:345 errors:0 dropped:0 overruns:0 frame:0 TX packets:271 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:256 RX bytes:24416 (23.8 KiB) TX bytes:14070 (13.7 KiB)/ # / #使用 service sshd restart 重启ssh服务 / # service sshd reloadReloading OpenBSD Secure Shell server's configuration./ # / # service sshd restartRestarting OpenBSD Secure Shell server: sshdCould not load host key: /etc/ssh/ssh_host_ecdsa_keyCould not load host key: /etc/ssh/ssh_host_ed25519_key./ #
四、重刷PKG固件 使用tftpd32工具临时搭建TFTP服务 本地防火墙允许Ping回显
在本地 Windows PC 终端上使用命令 ping 192.168.222.220 -n 3 测试网络连通性 ping 192.168.222.220 -n 3正在 Ping 192.168.222.220 具有 32 字节的数据:来自 192.168.222.220 的回复: 字节=32 时间=18ms TTL=63来自 192.168.222.220 的回复: 字节=32 时间=134ms TTL=63来自 192.168.222.220 的回复: 字节=32 时间=6ms TTL=63192.168.222.220 的 Ping 统计信息: 数据包: 已发送 = 3，已接收 = 3，丢失 = 0 (0% 丢失)，往返行程的估计时间(以毫秒为单位): 最短 = 6ms，最长 = 134ms，平均 = 52ms使用ssh工具(推荐使用putty)连接Modem
使用命令 tftp_package.sh 192.168.222.221 evo_x5_bsp-15.0.5.1.pkg 升级BSD部分固件 注意：需要增加临时交换分区大小，3.2版本及以上的版本需要扩大空间到32M~50M，不是原先的16M，并且刷入每个PKG包时都要增加临时分区大小。 # mount -t tmpfs -o remount,size=32M /tmp# # tftp_package.sh 192.168.222.221 evo_x5_bsp-15.0.5.1.pkgDownloading package evo_x5_bsp-15.0.5.1.pkgExtracting package evo_x5_bsp-15.0.5.1.pkgInstalling package evo_x5_bsp-15.0.5.1.pkg========== Package Installation script starting ==========Determining board model/hardware family: DONEValidating board model/hardware family: DONERemounting /tmp filesystem (6m): DONECleaning up from any previous install: DONEDetermining free space on flash filesystem: DONEEnsure all required files can be installed: DONEDetermining free space in /tmp/package: DONERunning package preinstall scriptlet:Create required directories: DONEInstalling files: DONECreate required sym-links: DONESaving install_file_map: DONERemounting /tmp filesystem (14m): DONE========== Package Installation script complete ==========Package evo_x5_bsp-15.0.5.1.pkg installed successfully#使用命令 tftp_package.sh 192.168.222.221 evo_x5_rmt-15.0.5.1.pkg 升级RMT部分固件 注意：需要增加临时交换分区大小，3.2版本及以上的版本需要扩大空间到32M~50M，不是原先的16M，并且刷入每个PKG包时都要增加临时分区大小。 # mount -t tmpfs -o remount,size=32M /tmp# # # tftp_package.sh 192.168.222.221 evo_x5_rmt-15.0.5.1.pkgDownloading package evo_x5_rmt-15.0.5.1.pkgExtracting package evo_x5_rmt-15.0.5.1.pkgInstalling package evo_x5_rmt-15.0.5.1.pkg========== Package Installation script starting ==========Determining board model/hardware family: DONEValidating board model/hardware family: DONERemounting /tmp filesystem (16m): DONECleaning up from any previous install: DONEDetermining free space on flash filesystem: DONEDetermining obsoleted file list/space: DONEDetermining obsoleted FPGA list/space: DONEEnsure all required files can be installed: DONEDetermining free space in /tmp/package: DONERunning package preinstall scriptlet: Remove any old package version files: DONERemoving obsolete files and unused FPGA images: DONECreate required directories: DONEInstalling files: DONECreate required sym-links: DONERunning package postinstall scriptlet: Ensure busybox links are correct: DONE Reconfigure modules.conf: DONE Setting SSHD services on: DONE Create and lock "admin" user account: DONE Install kernel image: DONE Running script (create_fpga_devices.sh): DONE Running script (create_cpld_devices.sh): DONE Running script (create_rawio_devices.sh): DONE Running script (create_eeprom_devices.sh): DONE Update module dependencies: DONE Setting "idirect_falcon" service on: DONESaving install_file_map: DONERemounting /tmp filesystem (6m): DONE========== Package Installation script complete ==========Package evo_x5_rmt-15.0.5.1.pkg installed successfully#使用命令 /usr/sbin/falcon --version 验证版本是否已经升级 # /usr/sbin/falcon --versionUsing OpenSSL 1.0.1j-fips 15 Oct 2014Starting Falcon...Code Version: 15.0.5.1Build Comment: Final_BuildBuild Label: IDS-15_0_5_1-Build-11~~~~~~~~falcon BUILD INFO: built Fri Feb 5 02:14:37 EST 2016 by root using g++ version 3.3 on Linux cm-build-rh5101-1 2.6.18-371.3.1.el5PAE #1 SMP Mon Nov 11 03:29:00 EST 2013 i686 i686 i386 GNU/Linux ~~~~~~~~#
五、重配opt文件 使用命令 tftp -p -r falcon_X5_232525.opt.bak -l falcon.opt 192.168.222.221 备份配置文件到远程服务器 使用命令 tftp -g -r _TDMA_Remote#_X5_232525.opt -l falcon_X5_232525.opt.new 192.168.222.221 下载配置文件到本地磁盘 # cd /etc/idirect/falcon/# # ls -alhdrwxrwxr-x 1 root root 0 Jan 1 01:41 .drwxrwxr-x 1 root root 0 Jan 1 00:07 ..-rw-r--r-- 1 root root 5.2k Jan 1 01:41 falcon.opt-rw-r--r-- 1 root root 5.2k Jan 1 01:11 falcon.opt.old-rwxr--r-- 1 root root 71 Jan 1 00:09 falcon_state.xml# # tftp -p -r falcon_X5_232525.opt.bak -l falcon.opt 192.168.222.221# # tftp -g -r _TDMA_Remote#_X5_232525.opt -l falcon_X5_232525.opt.new 192.168.222.221# # chmod 644 falcon_X5_232525.opt.new # # ls -alhdrwxrwxr-x 1 root root 0 Jan 1 01:44 .drwxrwxr-x 1 root root 0 Jan 1 00:07 ..-rw-r--r-- 1 root root 5.2k Jan 1 01:41 falcon.opt-rw-r--r-- 1 root root 5.2k Jan 1 01:11 falcon.opt.old-rw-r--r-- 1 root root 5.2k Jan 1 01:44 falcon_X5_232525.opt.new-rwxr--r-- 1 root root 71 Jan 1 00:09 falcon_state.xml# # mv falcon_X5_232525.opt.new falcon.optmv: overwrite 'falcon.opt'? y# # ls -alhdrwxrwxr-x 1 root root 0 Jan 1 01:44 .drwxrwxr-x 1 root root 0 Jan 1 00:07 ..-rw-r--r-- 1 root root 5.2k Jan 1 01:44 falcon.opt-rw-r--r-- 1 root root 5.2k Jan 1 01:11 falcon.opt.old-rwxr--r-- 1 root root 71 Jan 1 00:09 falcon_state.xml# #使用命令 cat falcon.opt 验证配置是否正确，没有额外的字符。 然后执行 reboot 命令，重启系统。 # cat falcon.opt[ANTENNA] addr = 172.26.102.18 connect_timeout = 30 dedicated_interface = ixp0 manufacturer = OpenAMIP max_skew = 90.000000 model = OpenAMIP port = 4002[BEAMS] beam_123 = MarineSat Network S2 maxbeam = 123[BEAMS_LOCAL] inhibit_tx_ifzero = 0 rxonly_enabled = 0 # !! Custom Parameter !![BTP] device_mode = tdma device_name = btp device_path = /dev[BTP_REQ] device_mode = tdma device_name = btp_req device_path = /dev[COMPRESSION] Threshold = 90[DEBUG] cpu_util_test_enabled = 0[DHCP_149] dhcp_dns_server2_ip = 0.0.0.0 dhcp_dns_server_ip = 10.188.147.1 dhcp_gateway_ip = 10.188.147.1 dhcp_lease_range = 10.188.147.50-10.188.147.254 dhcp_lease_seconds = 43200 dhcp_mode = 1[DNS_149] dns_cache_size = 100 dns_cache_ttl_max = 86400 dns_cache_ttl_min = 300 dns_enable = 1 dns_forward_queue_size = 1000 dns_forward_timeout = 2000 dns_primary_server_addr = 202.106.0.20 dns_primary_server_name = ns1 dns_secondary_server_addr = 114.114.114.114 dns_secondary_server_name = ns2[DVBS2] frame_length = 125.000000 frame_size = short mode = acm ncr_interval = 3375000 pilot = 1 rc_roll_off = 0.200000[ENC] auth_level_required = 0 enc_enabled = 0 enc_layer_enabled = 0 enc_mode = 0 peer_mode = 1[ETH0] interface = ixp0 phy_count = 1[ETH0_1] address = 172.26.102.17 netmask = 255.255.255.248 rip_enabled = 0 web_server_enabled = 0[ETH0_149] address = 10.188.147.1 group1 = 225.1.2.1 netmask = 255.255.255.0 rip_enabled = 0 web_server_enabled = 0[FREQ_TRANS] down_translation = 9750.000000 up_translation = 12800.000000[GUI_SERVER_PROXY] port = 14599[LAN] lan_gw_ip = 0.0.0.0 lan_ip = 172.26.102.17 lan_subnet_ip = 255.255.255.248[MAPSERVER_0] hostname = 172.16.126.3 port = 5003[MOBILE] gps_input = 2 init_tx_power_offset = 0.000000 is_mobile = 1 latlong_fail_interval = 10 latlong_interval = 300 tx_handshake_enabled = 0[MODEM_INSTALLATION] reflector_offset_angle = 0.000000 remote_lat = 0.000000 remote_long = 0.000000 spacecraft_long = 87.500000[MODEM_PARAMETERS] ref_carrier_fec_block_size = 170 ref_carrier_modcod_coding_rate = 2 ref_carrier_modcod_modulation = 1 ref_carrier_symbol_rate = 468000.000000 rx_acqrange = 70000 rx_diff = 0 rx_freq = 1441000000 rx_mode = 2 rx_only = 0 rx_scram = 1 rx_specinv = 0 rx_symrate = 8333000.000000 tx_bitrate = 1 tx_power_in_dbm = -20.000000 tx_specinv = 0[NET_ENC] id = 3 is_encrypted = 0[NMS] broadcast_ip = 172.16.126.5 download_monitor_credentials = 1 download_monitor_group = 239.192.0.0 download_monitor_port = 9000 event_server_ip = 172.16.126.5 event_server_port = 2860 generated_by = NMS-15.0.5 is_nms_managed = 1 keep_alive_port_number = 2860 NRD_remote_status_port_number = 2859 NRD_server_ip = 172.16.126.4 server_ip = 172.16.126.5 service_monitor_interval = 1000 timeout = 20000[ODU] lnb_dc_voltage = 13 lnb_tone_enable = 0 music_present = 0 odu_disable_tx_pwm = 0 odu_rx_10_mhz = 0 odu_rx_dc_power = 1 odu_tx_10_mhz = 1 odu_tx_clk_ref = 10 odu_tx_dc_power = 1[OOB] mem_high_percent = 90 mem_low_percent = 75[OPTIONS_FILE] carrier_type = 0 code_version = 15.0.5.4 did = 117673037 disable_options_flash_command = 0 generated_by = NMS-15.0.5 is_mesh = 0 mobile_remote_type = 1 modem_hardware = X5 modem_sn = 232525 modem_type = Remote product_mode = dvbs2 upstream_product_mode = idirect_tdma[POWER_MANAGEMENT] enable = 0 sleep_timeout = 0[ROUTE_149_0] gateway = 0.0.0.0 interface = sat0 metric = 1 netmask = 0.0.0.0 network = 0.0.0.0[ROUTE_1_0] gateway = 0.0.0.0 interface = sat0 metric = 1 netmask = 0.0.0.0 network = 0.0.0.0[RX1] device_mode = scpc device_name = rx1 device_path = /dev[SAT0_1] address = 10.252.102.17 netmask = 255.255.255.0 rip_enabled = 0 web_server_enabled = 0[SAT0_149] address = 10.252.102.17 netmask = 255.255.255.0 rip_enabled = 0 web_server_enabled = 0[SATELLITE] channelname = MarineSat Network S2 hunt_bandwidth = 10.000000 hunt_frequency = 1441.000000 longitude = 87.500000 max_lat = 0.000000 max_skew = 90.000000 min_look_angle = 0.000000 name = Chinasat 12 noise_reference_frequency = 0.000000 pol_skew = 0.000000 polarity = V rx_lcl_osc = 9750.000000 skew_margin = 90.000000 tx_bandwidth = 0.500000 tx_frequency = 1091.780000 tx_lcl_osc = 12800.000000 tx_polarity = H[SECURITY] admin_password = $idi3$.5fQ65$/njZwHXxJa9NQtOAi.N8bPcgOdRrOH79f38xJIZrdmeP3K9YTU/Zj1QGI0kIfLt6HgXDkLlNir3GJqHMCaTFa6 os_password = $1$0CppNk$VY2vgnKsOnee79OI1tgOI/ password = $idi3$1Z3fZ5$/7NGF5kb029RzILehP2NV3sjkfu9Zb3QPfb69shTneOJi1i6ZuSdQGoaRAYZ3Tn2WTqbwiEIv8yjw3/3dZYdkE[SOF] device_mode = tdma device_name = sof device_path = /dev[SYSTEM_TRAY] interval = 5000 mode = 1 port = 2859 server = 172.16.126.4 service_monitor_group = 239.255.255.1 service_monitor_port = 9001[TDMA] tx_watchdog_timeout_in_frames = 2[TX] device_mode = tdma device_name = tx device_path = /dev[TX_SOF] device_mode = tdma device_name = tx_sof device_path = /dev[UCP] max_power_level_in_db = -15.000000 power_uplink_control_processing = 1[UDP] force_rtp_fullheader = 1 force_udp_fullheader = 1 max_hdr_comp_packet_size = 180 passthru = 1 payload_comp = 0[VLAN] mode = 1 vid = 149# # reboot#
====================== 步骤适用于 3000系列、5000系列、X3、X5 类型的小站，对于X1与X7不适用。 配置文件必须是 Unix(LF) 的编码，且末尾不能有特殊的字符。 如果文件换行格式为 Window(CR LF) ，则可以使用 Notepad++ 软件来进行转码。
由于opt文件的原因，可能文件不完整，或者写入的opt文件版本不正确的原因都会导致Modem重启后出现下面的故障现象： 小站Status亮红灯 小站反复重启 此时，需要更新Modem中的opt文件了。但是iSite又不能正常连接Modem导入opt文件，此时只能通过console的方式来手动更新opt文件。在修复前，需要弄清楚Modem当前的版本以及准备好正确的opt文件。 1. 通过SSH或者串口以root用户名进入Modem。SSH的方式是使用putty等支持SSH的软件通过网络直连modem。 2. 按照提示输入用户名root和密码 3. 输入下面的命令停掉falcon应用，防止Modem重启 # service idirect_falcon stop4. 进入到opt在modem中存放目录/etc/idirect/falcon，可以通过ls查看当前目录下的文件，通过mv等命令备份当前的opt文件 # cd /etc/idirect/falcon# # ls -l#5. 在电脑上使用记事本打开已经准备好的该Modem对应版本的opt文件，并复制到剪切板 6. 使用cat命令打开或者创建一个新的falcon.opt文件 # cat > /etc/idirect/falcon/falcon.opt此时进入到falcon.opt文件的编辑模式，并且falcon.opt文件中的内容被清空。 7.将剪切板中的内容复制到falcon.opt文件 8. 复制结束后回车，同时按下ctrl+d键退出编辑模式 9. 通过ls命令查看目录下是否有falcon.opt文件存在 # ls -l /etc/idirect/falcon10. 使用cat命令查看falcon.opt文件内容 # cat /etc/idirect/falcon/falcon.opt11.重新启动falcon应用，观察status LED是否恢复正常 service idirect_falcon restart
========================== 系统启动输出信息 # dmesg Linux version 2.4.24-uc0-iDirect0 (root@EmbEserver75) (gcc version 3.3.2) #1 Wed Jun 15 12:44:25 EDT 2011CPU: XScale-IXP4xx/IXC11xx revision 2Machine: iDirect Phoenix Platformalloc_bootmem_lowmemtable_initSecurity risk: creating user accessible mapping for 0x51000000 at 0xf1000000On node 0 totalpages: 32768zone(0): 16384 pages.zone(1): 16384 pages.zone(2): 0 pages.Kernel command line: console=ttyS1,9600 root=/dev/mtdblock2Relocating machine vectors to 0xffff0000Calibrating delay loop... 532.48 BogoMIPSMemory: 128MB = 128MB totalMemory: 127388KB available (1680K code, 477K data, 72K init)Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)Inode cache hash table entries: 8192 (order: 4, 65536 bytes)Mount cache hash table entries: 512 (order: 0, 4096 bytes)Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)Page-cache hash table entries: 32768 (order: 5, 131072 bytes)POSIX conformance testing by UNIFIXPCI: bus0: Fast back to back transfers enabledLinux NET4.0 for Linux 2.4Based upon Swansea University Computer Society NET3.039Initializing RT netlink socketStarting kswapdJFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.i2c-core.o: i2c core modulei2c-dev.o: i2c /dev entries driver modulei2c-core.o: driver i2c-dev dummy driver registered.i2c-algo-bit.o: i2c bit algorithm modulei2c-proc.o version 2.6.1 (20010825)pty: 256 Unix98 ptys configuredSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabledttyS00 at 0xff000003 (irq = 15) is a XScale UARTttyS01 at 0xff001003 (irq = 13) is a XScale UARTUniversal TUN/TAP device driver 1.5 (C)1999-2002 Maxim KrasnyanskyUniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxixp425_init: Window Size = 33554432IXP425 Flash: Found 1 x16 devices at 0x1000000 in 16-bit modecfi_cmdset_0001: Suspend erase on write disabled.0: offset=0x0,size=0x20000,blocks=1281: offset=0x1000000,size=0x20000,blocks=128Using buffer write methodCreating 6 MTD partitions on "IXP425 Flash":0x00000000-0x00040000 : "RedBoot"0x00060000-0x00160000 : "Linux"0x00160000-0x01fe0000 : "RootFS"0x01fe0000-0x01fff000 : "FIS directory"mtd: partition "FIS directory" doesn't end on an erase block -- force read-only0x01fff000-0x02000000 : "RedBoot config"mtd: partition "RedBoot config" doesn't start on an erase block boundary -- force read-only0x01fe0000-0x02000000 : "FIS Overlap"Board has 65nm flash partpktgen.c: v1.3: Packet Generator for packet performance testing.pktgen: Error: your machine does not have working cycle counter.NET4: Linux TCP/IP 1.0 for NET4.0IP Protocols: ICMP, UDP, TCP, IGMPIP: routing cache hash table of 1024 buckets, 8KbytesTCP: Hash tables configured (established 8192 bind 16384)IPv4 over IPv4 tunneling driverGRE over IPv4 tunneling driverLinux IP multicast router 0.06 plus PIM-SMip_conntrack version 2.1 (1024 buckets, 8192 max) - 320 bytes per conntrackip_conntrack_pptp version $Revision: 1.1.1.1 $ loadedip_nat_pptp version $Revision: 1.1.1.1 $ loadedip_tables: (C) 2000-2002 Netfilter core teamipt_time loadingipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/arp_tables: (C) 2002 David S. MillerNET4: Unix domain sockets 1.0/SMP for Linux NET4.0.IPv6 v0.8 for NET4.0IPv6 over IPv4 tunneling driverip6_tables: (C) 2000-2002 Netfilter core teamregistering ipv6 mark target802.1Q VLAN Support v1.8 Ben Greear Other stuff added by David S. Miller NetWinder Floating Point Emulator V0.97 (double precision)VFS: Mounted root (jffs2 filesystem).Freeing init memory: 72KModule init.ixp425_eth: Initializing IXP425 NPE Ethernet driver software v. 0.1.9 (1_4)ixp425_eth: ixp0 is using the PHY at address 0ixp425_eth: ixp1 is using the PHY at address 1ixp425_eth: CPU clock speed (approx) = 532 MHzfpga: Feb 5 2016 01:46:43cpld: Feb 5 2016 01:46:41rawio: Feb 5 2016 01:46:56fpga: Exitfpga: Feb 5 2016 01:46:43ixp0: no IPv6 routers presenti2c-dev.o: Registered 'FPGA-I2C Adapter' as minor 0i2c-core.o: adapter FPGA-I2C Adapter registered as adapter 0.i2c-opencore: __DATE__ __TIME__ i2c-core.o: driver stv0900 registered.i2c-core.o: client [stv0900] registered to adapter [FPGA-I2C Adapter](pos. 0).stv0900: Feb 5 2016 01:46:58i2c-core.o: driver stb6100 registered.i2c-core.o: client [stb6100] registered to adapter [FPGA-I2C Adapter](pos. 1).stb6100: Feb 5 2016 01:46:57PCI: enabling device 00:0e.0 (0000 -> 0002)ixp425_eth: ixp0: Entering promiscuous modedevice ixp0 entered promiscuous modeCPU和内存以及系统版本信息 # cat /proc/cpuinfo Processor : XScale-IXP4xx/IXC11xx rev 2 (v5b)BogoMIPS : 532.48Features : swp half thumb fastmult edsp Hardware : iDirect Phoenix PlatformRevision : 0000Serial : 0000000000000000# # cat /proc/meminfo total: used: free: shared: buffers: cached:Mem: 130519040 30400512 100118528 0 0 15392768Swap: 0 0 0MemTotal: 127460 kBMemFree: 97772 kBMemShared: 0 kBBuffers: 0 kBCached: 15032 kBSwapCached: 0 kBActive: 7948 kBInactive: 8736 kBHighTotal: 0 kBHighFree: 0 kBLowTotal: 127460 kBLowFree: 97772 kBSwapTotal: 0 kBSwapFree: 0 kB# # cat /etc/idirect-release iDirect Linux-BSP Release 15.0.5.1# # uname -aLinux iDirect 2.4.24-uc0-iDirect0 #1 Wed Jun 15 12:44:25 EDT 2011 armv5b unknown#
================ End
|
【本文地址】
今日新闻 |
推荐新闻 |